sales@mzdinductionhob.com +86 137 5113 5172

Case

UK Project Case : Smart Power Allocation for a 4-Zone Induction Hob

UK

Delivering High-Power Cooking Functionality with a Standard UK 13A Plug

Product: 4-Zone Built-in Induction Hob

Target Market: United Kingdom

Key Requirement: Plug-in installation using a standard UK 13A plug

Engineering Challenge: Managing the combined power demand of four cooking zones

Solution: Software-based dynamic power allocation

Reported Commercial Result: Initial order of 1,500 units, followed by a reorder of 3,610 units

1. Project Background

A UK-based kitchen appliance distributor approached MZD to develop a four-zone built-in induction hob for the residential market.

The customer wanted a product offering the flexibility of four independent cooking zones while using a standard UK 13A plug.

This requirement was important for the intended market because a plug-in product can simplify installation in suitable kitchens where the existing electrical supply and installation conditions are appropriate.

The challenge was to combine the product’s multi-zone cooking capability with the power limitations of a standard domestic plug-in connection.

2. The Challenge: Four Cooking Zones, One Limited Power Supply

The proposed induction hob featured four independent cooking zones, each capable of delivering up to approximately 1,500W or 2,000W, depending on the zone.

The combined rated power of the four zones was approximately 7,000W.

However, a 13A connection at a nominal 230V corresponds to approximately 2,990W of theoretical input power. The product therefore could not operate all four zones simultaneously at their individual maximum power through this connection.

The customer needed a practical solution that would:

  • Support installation using a standard UK 13A plug.
  • Manage the appliance's total input power within the designed limit.
  • Retain strong single-zone cooking performance.
  • Allow users to operate multiple cooking zones without requiring manual power calculations.
  • Provide a consistent and practical cooking experience for residential users.

Rather than treating this as a simple reduction in rated power, MZD approached it as a product control and power-management challenge.

3. The Engineering Solution: Dynamic Power Allocation

MZD’s engineering team developed a software-based Dynamic Power Allocation (DPA) strategy for the plug-in version.

The system was designed with a global input power limit of 2,800W. When multiple cooking zones were operating, the controller managed the available power across the active zones so that their combined input remained within the configured limit.

The objective was to make power management part of the product’s normal operation rather than requiring users to manage the limitation themselves.

Single-Zone Operation

When only one cooking zone is active, it can use the available power permitted by the selected zone’s specification and the system’s operating limits.

This allows the product to retain its specified single-zone performance where the configured power limit permits it.

Multi-Zone Power Sharing

When two or more zones are active, the controller distributes the available power according to the product’s control logic.

If several zones request high power at the same time, the available power is shared rather than allowing the combined demand to exceed the configured total limit.

The actual power delivered to each zone depends on the selected settings, the number of active zones and the controller’s allocation strategy.

Boost Function Management

When Boost is activated, the control system manages the available power across the active zones to maintain the configured total input limit.

This allows the product to prioritize a requested high-power operation while adjusting the power available to other zones, according to the programmed control logic.

Four-Zone Interlocking

All four zones operate under the system’s total-power management strategy.

The control system is designed to coordinate different combinations of active zones within the configured input power limit, rather than treating each zone as an independent load with unrestricted simultaneous output.

4. Validation and Product Development

Following the software development work, MZD produced updated samples for evaluation.

According to the project records, the updated plug-in version was submitted to a UKAS-accredited testing laboratory and passed the reported electrical safety tests for the intended application.

The customer subsequently completed the UKCA conformity process for the plug-in version.

For products intended for the UK market, power management must be considered alongside the complete appliance design, including electrical protection, thermal performance, wiring, plug and cable ratings, and the applicable conformity assessment requirements.

The power-allocation function is one part of the overall product design; it does not replace complete-product safety testing or regulatory compliance.

5. Commercial Results

The project progressed from engineering development to commercial supply.

According to the project records:

  • Initial order: 1,500 units
  • Follow-up order: 3,610 units
  • Total across these two orders: 5,110 units

The repeat order provided a tangible commercial indicator that the product had progressed beyond the initial development stage and continued to be supplied to the customer’s market.

For MZD, the project demonstrated the value of aligning product control logic with a customer’s installation requirements and intended market.

6. What This Project Demonstrates

This project illustrates an important principle in appliance development: a product’s individual component specifications do not always determine how the complete appliance should operate in its target market.

A four-zone induction hob may have a combined zone rating of approximately 7,000W, while the intended domestic connection places a lower limit on the total input power available at any one time.

The engineering task is to develop an appropriate system-level solution that balances power management, user operation and the applicable safety requirements.

For appliance brands and importers, this kind of early technical coordination can help align product design with real installation conditions before a product enters the market.

7. How MZD Can Support Your Next Project

MZD works with international OEM/ODM customers on induction cooking products and project-specific requirements.

Depending on the product and agreed development scope, discussions may cover:

  • Multi-zone power management
  • Total input power limits
  • Single-zone and multi-zone operating behaviour
  • Boost function logic
  • Electrical supply and plug requirements
  • Software and control-system customization
  • Product samples and technical evaluation
  • Manufacturing and supply coordination
  • The available functions, specifications and conformity documentation depend on the selected model and destination market.

Developing an Induction Hob for Your Market?

Whether you are developing a plug-in induction hob for the UK, a higher-power model for a dedicated electrical circuit, or a customized product for another market, MZD welcomes early discussions about your requirements.

MZD — Practical Engineering Solutions for International Induction Appliance Brands

Contact us to discuss your product concept, target market and technical requirements.

WhatsApp Email Inquiry