Russian Project Case : How MZD Reduced Induction Cooktop Fan Noise and Secured a 1,740-Unit Order
RUSDeveloping a Low-Noise Induction Cooktop with Intelligent Fan Speed Control for a Russian Distributor
1. Project Background
A Russian kitchen appliance distributor approached MZD to develop a customized induction cooktop for the local market.
As an induction cooktop manufacturer supporting OEM/ODM product development, MZD supplied initial engineering samples for the client’s evaluation. The customer was satisfied with the heating performance and overall build quality but identified one area for improvement: cooling fan noise during operation.
For the client, reducing operating noise without compromising cooling performance or product reliability was an important requirement before moving into mass production.
This gave MZD an opportunity to refine the product at the sample development stage, before the design was finalized for bulk production.
2. The Challenge: Reducing Fan Noise Without Compromising Cooling Performance
During sample testing, the Russian distributor found that the induction cooktop’s cooling fan was noticeably louder than expected.
Our engineering investigation identified the main cause: the original fan control logic activated the fan as soon as the cooktop was powered on, regardless of the actual temperature of the internal components or the cooking load.
This meant the fan could run unnecessarily during lighter cooking tasks, such as simmering soup or warming milk, when immediate full-speed cooling was not required.
The challenge was to develop a low-noise induction cooktop with intelligent fan control that could:
- Reduce unnecessary fan operation during low-temperature cooking.
- Adjust cooling speed according to actual thermal conditions.
- Maintain adequate cooling for critical electronic components.
- Improve the overall user experience without compromising product reliability.
Rather than treating fan noise as an unavoidable characteristic of induction cooking, MZD approached it as an engineering problem that could be addressed through improved thermal management and firmware optimization.
3. Engineering Solution: Three-Stage Intelligent Fan Speed Control
MZD’s engineering team redesigned the fan control logic using real-time temperature monitoring of two key areas: the IGBT (Insulated Gate Bipolar Transistor) and the cooktop glass surface.
The revised firmware introduced a three-stage fan speed regulation system.
How the Intelligent Fan Control Works
Stage 1 — Fan Off During Low-Temperature Operation
When the monitored temperatures remain below the activation thresholds, the fan stays off (0 V). This eliminates unnecessary fan noise during suitable low-temperature operating conditions.
Stage 2 — Half-Speed Cooling When Needed
When the IGBT temperature exceeds 45°C or the glass surface temperature exceeds 55°C, the fan operates at half speed (12 V), providing cooling without immediately running at full speed.
Stage 3 — Full-Speed Cooling at Higher Temperatures
When the IGBT temperature exceeds 60°C or the glass surface temperature exceeds 80°C, the fan switches to full speed (18 V) to provide increased cooling when thermal demand rises.
Key Engineering Benefits
Reduced unnecessary fan operation: The fan does not automatically run at full speed from startup when cooling demand is low.
Temperature-based speed regulation: Fan operation responds to monitored thermal conditions rather than relying solely on a fixed startup sequence.
- Balanced noise and cooling performance: Half-speed operation provides an intermediate cooling level between fan-off and full-speed operation.
- Thermal protection remains a priority: Full-speed cooling is activated when either monitored temperature reaches its specified upper threshold.
The objective was not simply to make the induction cooktop quieter. It was to improve the balance between operating noise, cooling performance and long-term product reliability.
4. Validation & Results
After completing the firmware modification, MZD prepared an updated batch of engineering samples and sent them to the Russian distributor for re-evaluation.
Following the revised sample evaluation, the project achieved the following results:
- Significantly reduced fan noise during routine cooking scenarios, including simmering, boiling and medium-heat cooking.
The fan remained off or operated at half speed for approximately 65% of typical cooking time under the reported test conditions.
- Thermal testing indicated that component temperatures remained within the applicable limits during the evaluated test conditions.
The Russian customer approved the updated samples and placed a formal order for 1,740 induction hobs incorporating the revised fan control logic.
By addressing the customer’s feedback before mass production, MZD helped turn a sample-stage concern into an approved product configuration and a confirmed commercial order.
5. Long-Term Business Impact
This project demonstrates how engineering responsiveness can directly support commercial success.
The customer did not simply need an induction cooktop supplier capable of meeting basic specifications. They needed a manufacturing partner willing to listen to feedback, investigate the underlying issue and improve the product before mass production.
MZD’s approach helped the project progress from initial sample evaluation to customer approval and a formal 1,740-unit order.
For distributors developing their own appliance ranges, this type of cooperation can be valuable. Early engineering feedback provides an opportunity to refine product performance before larger quantities are manufactured, helping align the final product more closely with market expectations.
Delivering a product is the starting point. A supplier’s real value becomes clear when it can turn customer feedback into a practical engineering improvement.
6. Lessons for Your Project
If you are sourcing an induction cooktop manufacturer for your own brand or distribution business, product specifications alone may not tell the whole story.
Operating noise, thermal management, control logic and user experience can all influence how a product performs in its target market.
When evaluating an OEM/ODM induction cooktop supplier, consider asking:
- Can the manufacturer adjust firmware and fan control logic to meet project-specific requirements?
- Can engineering samples be modified and re-evaluated before mass production?
- How does the manufacturer balance noise reduction with electronic component cooling?
- Can the supplier respond to technical feedback and support product refinement throughout development?
MZD supports international B2B customers with customized induction cooktop development, engineering sample evaluation and product improvements based on project requirements.
Whether you need a low-noise induction cooktop, a customized built-in induction hob or an OEM/ODM induction cooking solution for your target market, our team can discuss the technical requirements with you.
Looking for an OEM/ODM induction cooktop manufacturer for your next project?
Contact MZD to discuss your product specifications, development goals and customization requirements.